How to Install a Sensi Thermostat

Installing a Sensi thermostat is a straightforward task that can be accomplished with minimum tools and in little time. Below we will guide you through the simple process, step by step.

Gather Necessary Tools

• Screwdriver: Flat head or Phillips depending on your existing thermostat and wall type.
• Level tool: This will help keep your installation neat and professional.
• Drill (optional): Depending on your wall type, you might need this to install screws.
• Drywall anchors(optional): If your wall requires it, drywall anchors can provide additional support for the screws.
• Cell phone or tablet: You’ll need this to download and configure the Sensi app for controlling your thermostat.

Turn Off Power to Your HVAC System

This is an important safety step before beginning any work on your thermostat. The power to your heating, ventilation, and air conditioning (HVAC) system can usually be turned off at the breaker box. Make sure to double-check that power has been safely disconnected before proceeding any further.

Remove the Old Thermostat

Now that everything is safe, you can proceed to remove your old thermostat. Start by taking off the outer casing or cover of the thermostat; this should simply snap off in most cases.

You’ll find a few wires connected; take a picture of this setup for future reference before disconnecting them. With labels provided in your Sensi package, label each wire according to where it was connected in old setup.

Install the Sensi Base Plate

Now it’s time to install the Sensi base plate. Hold the base plate against the wall where you want to install it and ensure it is level. Mark screw hole locations with a pencil.

Depending on your wall type, you might need to drill holes for the screws – use drywall anchors if necessary. Screw in the base plate being careful not to over-tighten.

Next, connect your HVAC system wires to the Sensi thermostat base following the reference picture taken during removal of old setup. Once completed, snap on the faceplate of your new Sensi thermostat.

Download and Configure the App

The final step is downloading and configuring your new Sensi thermostat. Locate and download the Sensi app from either Google Play or Apple’s App Store depending on your device.

Once downloaded, open up the app and create an account if you don’t already have one. Follow through with adding a new thermostat by scanning or manually entering its serial number found at backside of device.

Follow in-app prompts for final setup configuration according to your heating/cooling system specifications which completes your installation process. Now, power back on your HVAC system at breaker box and enjoy effortless control over your environment with Sensi Thermostat!

Gather Necessary Tools

• A screwdriver: This is a fundamental tool for any installation job. You’ll need both flathead and Phillips-head screwdrivers.
• A drill: If your wall doesn’t have pre-existing holes, you will need a drill to make new ones. The type of drill bit will depend on your wall material (plaster, drywall or wood).
• Wire strippers: These are necessary if your thermostat wires are not already bare.
• Level tool: This tool will help ensure that you install the base plate perfectly horizontal.
• Labels or masking tape and a pen: To label the wires during removal of old thermostat.

Prepare these tools ahead of time to make sure that everything runs smoothly once you start the process of installing your Sensi thermostat.

The installation guide may specify additional or different tools based on specific model features and requirements. Always refer to the provided instruction manual for detailed information about what you might need for your specific model Sensi thermostat.

Once all these items are in place, move on to turning off power to your HVAC system as safety precaution before removing old thermostat and installing new one.

Remove the Old Thermostat

Before you embark on this operation, be sure to consult the original user manual for your old thermostat as it may contain specific instructions for safe removal. If you no longer have the user manual, you might be able to find a digital copy online by searching the model number.

Firstly, take off the thermostat’s faceplate. Most thermostats have simple clip systems that you can gently tug on to remove. Some might require a small screwdriver.

• Taking a clear photograph of the wiring with your phone
• Drawing a diagram of where each wire goes
• Labelling each wire by using masking tape and a pen

After recording the wiring configuration, you can proceed to disconnecting them. The wires are usually held in place by small screws, which can be loosened with the help of a screwdriver.

The next step is removing your old thermostat base from the wall. Again, this is typically held in place by screws which you can unscrew with ease.

Once you have successfully removed the old thermostat base from the wall, ensure you do not discard it immediately especially if it contains mercury tubes because these need special handling and disposal procedures due to their potential toxicity.

You have now successfully removed your old thermostat and are one step closer to enjoying the comfort and convenience of your new Sensi smart home device!

1. Remove Faceplate
2. Record Wiring Configuration
3. Disconnect Wires
4. Remove Thermostat Base
5. Dispose Carefully if Mercury Tubes are Present

Install the Sensi Base Plate

The Sensi base plate installation is a critical step in the process of installing your Sensi thermostat. It forms the foundation for attaching the thermostat to your wall and wiring it to your home’s heating, ventilation, and air conditioning (HVAC) system. Here we will guide you through this procedure in a manner that is easy to understand.

Firstly, identify the type of HVAC system in operation at your home. This is of utmost importance because it determines which wire goes where on the base plate. If you are unsure about this, consider consulting an HVAC specialist or referring to your HVAC system’s manual.

• Identify any labeling on the wires coming out from your wall. These labels correspond to terminals on the back of your old thermostat and should match those on the new Sensi base plate.
• If there are no labels, take a photo before disconnecting any wires from your old thermostat. This will serve as a personal reference when connecting these wires to your new Sensi base plate.
• Loosen the terminal screws on the Sensi base plate using a screwdriver and insert each wire into its corresponding terminal.
• After inserting each wire, tighten its terminal screw to secure it in place.

1. Align your Sensi base plate with previously marked drilling points or holes (from removal of old thermostat).
2. Using one hand, hold up the base plate against the wall while with other hand, drill appropriate sized screws into each hole.
3. Ensure that all screws are tight and that the base plate sits flush against your wall.
4. Use built-in level tool on Sensi backplate to ensure it is evenly mounted.

In the next few steps, you will mount the Sensi thermostat on this base plate and connect it to your HVAC system. Be sure to take your time and double-check all connections. Incorrect wiring can cause damage to the thermostat or HVAC system.

Once you have installed the base plate, you are ready to move on to setting up the Sensi app. This app will allow you to control your Sensi thermostat from anywhere, providing flexible temperature control and potentially energy savings. The installation process may seem intricate, but with patience and attention to detail, you’ll be well on your way to enjoying a more efficient and comfortable living environment.

Download and Configure the App

• Go to your device’s app store (Google Play Store for Android users or Apple App Store for iOS users).
• In the search field, type “Sensi” then select “Sensi Thermostat” from the search results.
• Click “Install” (for Android) or “Get” (for iOS) to download the app.

• Click on “Create New Account.”
• Enter your details and accept terms and conditions.
• You will receive an activation email, click on it to activate your account.

• On the main dashboard of the Sensi app, tap on “+ Add Device.”
• The screen will prompt you to scan or manually enter a code found at the back of thermostat or in its instruction manual.
• Once entered correctly, it’ll ask you for your Wi-Fi details.

• Set schedules: You can program specific temperature settings for different times of day.
• Adjust temperature remotely: The app allows you to change room temperature from any location.

Remember that each feature available in-app depends on the specific Sensi model you’ve installed. For example, some models feature geofencing, which sets your thermostat to ‘Away’ mode when your mobile device leaves a preset boundary. This capability may not be available in all models.

The Sensi app also enables you to receive important alerts about your HVAC system’s operation and maintenance needs. It can notify you of temperature shifts outside your set range or remind you when it’s time to change air filters.

In summary, downloading and configuring the Sensi app is a critical part of the thermostat installation process. The app will provide full control over your HVAC system from virtually anywhere, ensuring comfort and efficiency at all times.

Download and Configure the App

Before you proceed with connecting your Sensi thermostat to your home’s HVAC system, it’s vital to download and configure the Sensi app on your smartphone or tablet. This step ensures that you can control your heating and cooling systems remotely and use all the advanced features that Sensi thermostats offer.

Step 1: Download the App

First, go to either Google Play Store or Apple App Store on your device. Once there, use the search bar at the top of the screen to find “Sensi”. The app should appear as “Sensi Smart Thermostat” by Emerson Climate Technologies, Inc. Download and install this application onto your device.

Step 2: Create Your Account

When you open the Sensi app for the first time, it will prompt you to create an account. Enter your email address and create a password following Sensi’s password guidelines. You’ll receive an email confirmation for account creation which you need to confirm.

Step 3: Add Your Thermostat

After confirming your account, log in using your new credentials. The app will guide you through adding a new thermostat. Find and select “Add Thermostat” from the menu.

Next, enter the unique equipment MAC ID found at most thermostats’ back or on its box. The MAC ID is usually a combination of numbers and letters (e.g., A1B2C3D4E5). Enter this code when asked by the application.

Step 4: Connect to Wi-Fi

Now, it’s time for connecting your Sensi thermostat with Wi-Fi. Go to phone settings > Wi-Fi > Choose a network > select “NewThermostat_123456.” Return back to Sensi Application after connecting with Wi-Fi.

Step 5: Configure Settings

After you successfully connect your Sensi thermostat with Wi-Fi, return to the app. It will ask you to choose a name for your thermostat and select the type of heating and cooling system you have at home. Make sure to provide accurate information so that the app can monitor and control your HVAC system properly.